Vibration Sensor Module (Normally Off)

Vibration Sensor Module (Normally Off)

    • THB37.75(VAT included)
  • Ex Tax: THB37.75
    • 10 ชิ้นขึ้นไป THB34.73
    • 50 ชิ้นขึ้นไป THB30.20
  • เงินคืน: 3%
  • ยอดคงเหลือ CytronCash: เข้าสู่ระบบ
  • สินค้าในสต๊อก:
  • รหัสสินค้า: SN-VIBRATE-MOD
  • ระยะเวลาในการรับประกัน: 12 เดือน
  • Shipping:

Simple to use vibration sensor module. Comes with SW-420 vibration sensor, integrated with adjustable sensitivity via on board potentiometer. And there are LED indicators for power and also digital output status. Simple and straight forward interface, just 3-pin, VCC, GND and the DO (digital output). Support 3.3V or 5V power.

This vibration sensor module is compatible with any microcontroller that have digital input. Of course popular microcontroller such and PIC, Arduino, Raspberry Pi are compatible. Direct interface is essential to use this sensor.

The DO will be logic LOW when there is no vibration, and indicator LED will light.

Example of applications:

  • Vibration detecting
  • Burglary protection system


  • The default state of the swith is close
  • Digital output
  • Supply voltage:3.3V-5V
  • On-board indicator LED to show the results
  • On-board LM393 chip
  • Dimension of the board: 3.2cm x 1.4cm


Vibration Sensor Module (Normally Off)

This video shows how Vibration Sensor Module (Normally Off) work. For example code and hardware setup please refer to this link: Please refer to the product page for more info:

Hi, what is the current rating for this module? ( Sam, 13/09/2020 )
Hi, we're sorry as we do not have the data for this ya. Thanks :)
Hi. Would like to ask about this item. The item can withstand in extreme low temperature and high temperature (-35 to 80)? What is the output value the sensor would give? ( Nabil, 31/10/2018 )
Hi, sorry we don't have any info from the supplier for the temperature range. 
May I know, once the sensor gets triggered, what is the DO form? spike form (based on vibration detection) or square form signal (for certain period).
recently I used SN-VBR-18010P and need to pair with Monostable Timer to get square form signal (as I needed).
( Ali, 28/03/2018 )
Hi, this is simple vibration sensor module. When vibration is detected, it will provide HIGH based on vibration. For further questions, please visit to our technical forum for similar question or post your question there, as this session is only for short inquiry. Thanks.
Does the output (DO) is vcc or fixed voltage output regardless how much vcc is applied? ( Sobri, 16/02/2018 )
Hi, the DO voltage should depends on the VCC. However we not verify yet. We will update any findings on the product page. Thanks.
can contact me via my email ( HAZIQ, 18/05/2017 )
Hi, for further questions you can post to our technical forum, as this session only for short inquiry. Thanks.
I have a few questions about your items:

1. Is that your item can receive a big vibration/impact ?
2. Whether the use of this tool can be installed / used at any time or in certain places?
3. Is that your item can produce a graph if the wire connect to laptop
( HAZIQ, 18/05/2017 )


1. You can adjust the sensitivity via on board potentiometer.

2 & 3. This only a sensor, you need a microcontroller and program it to suit your application.

For further questions you can post to our technical forum, as this session only for short inquiry.

Ask a question

Note: HTML is not translated!
  • 5 out of 5
ความคิดเห็นทั้งหมด (23)
  • 5
  • 4
  • 3
  • 2
  • 1

แท็ก: Arduino sensor, Sensor, Vibration sensor, vibrate, sensor module