XBee Pro 60mW Wire Antenna - Series 1

XBee Pro 60mW Wire Antenna - Series 1

  • สินค้าในสต๊อก:
    Discontinued
  • รหัสสินค้า: XBEE-PRO
  • ระยะเวลาในการรับประกัน: 12 เดือน
Having fun with XBee module? Now Cytron Technologies offer higher power (longer communication range) XBee, the XBee Pro. It has similar specification with XBee module, except the transmit power is higher which result in greater wireless communication range, up to 750meters (LOS). The communication protocol, pin layout and arrangement is fully compatible with XBee, thus it can be fitted in to SKXBee. It allows very simple yet reliable wireless communication between microcontroller, computer, or any system with serial communication. Both Point to point and point to multipoint communication are supported. Since XBee Pro pin is 2mm pitch to pitch and 3.3V system, please consider SKXBEE as starter kit.
 
Note: Please download the latest X-CTU installer here.
 
Product Specification:
  • ISM 2.4 GHz operating frequency
  • 60 mW (+18 dBm) power output (up to 750m)
  • Industrial temperature rating (-40° C to 85° C)
  • Indoor/Urban range: up to 300 ft (100 m)
  • Outdoor/RF line-of-sight range: 750meters
  • Interface data rate: Up to 115.2 Kbps
  • Operating frequency: 2.4 GHz
  • Supply voltage: 2.8 - 3.4 V
  • Transmit current: 270 mA (@ 3.3 V)
  • Receive current: 55 mA (@ 3.3 V)
  • Power-down sleep current: <10 µA
  • 2mm pitch to pitch DIP pin
  • Wire Antenna
  • Dimension: 2.438 cm x 3.294 cm
Package included:
Please check out for our XBee Tutorials:

 

 

 

May i know it is compatible in Arduino Uno and Matlab? Thanks ( loo, 13/03/2016 )

Hi. It does compatible with Arduino Uno. As for Matlab, we are not familiar with Matlab but you can try to experiment. Thanks. :)

Hello Cytron. How many shipping days before I accept the Xbee? Im from the Philippines. ( Tauts, 02/02/2016 )

Hi, you can refer here under shipping policies for Shipping Method and its delivery time. Estimated delivery time is 3 to 5 days through DHL International courier service. Thanks. :)

Hi Cytron, Can this device communicate directly through computer wifi? ( anas, 02/07/2015 )

Hi, This device cannot communicate directly through computer wifi. It has to be pair with same module. 

Hi Cytron, Does this product support DigiMesh ? ( Zohan, 08/05/2015 )

Well, you need to reload the firmware with digimesh. Here is one tutorial for you to refer.

Hello, I want to confirm, do you have XBee Series 1 in stock? Need 10 unit. Thanks ( Anwar, 18/03/2015 )

Yup, you can check the stock right in the product page, the "Availability" shows the stock we have, currently there are 137 pcs.

Hi cytron saya sudah cuba untuk communicate antara 2 xbee pro s1, tapi tidak berjaya, ada tutorial cara untuk setup xbee pro s1?? ( nazrin, 06/03/2015 )

Actually XBee PRO S1 is the same as XBee S1 in term of settings for communication :) There are plenty of tutorials that you can refer, even the datasheet explain it. The User's Manual of SKXBee also have example for that. If you have further inquiry, please do discuss in our technical forum as this section is for short inquiry, thanks :)

Hi Cytron, Is it possible to used this Xbee, with arduino uno ? Because the max current consumption for this device is 270mA @3.3v, but arduino 3.3v only can supply up to 150mA @3.3V ....kindly assist me about this matter .. thanks.. ( shaffiq, 29/01/2015 )

If you use proper shield such as XBee shield, it has 3.3V regulator that will proper sufficient power to the XBee.

Ask a question

Note: HTML is not translated!
  • 0 out of 5
                  
ความคิดเห็นทั้งหมด (0)
  • 5
    0%
  • 4
    0%
  • 3
    0%
  • 2
    0%
  • 1
    0%

แท็ก: xbee, pro, 60mw, wire, antenna, series, and xbee-pro