Raya Holiday (ปีใหม่มาเลเซีย) ทางบริษัทขอแจ้งให้ทราบว่าทุกออเดอร์หลังจากวันที่ 11 พ.ค. 64 (วันอังคาร) ตั้งแต่ 11.00น. เป็นต้นไป จะจัดส่งอีกครั้งในวันที่ที่ 17 พ.ค. 64 (วันจันทร์)
New -14% 120GB 2.5-inch MakerDisk SATA III SSD with RPi OS

120GB 2.5-inch MakerDisk SATA III SSD with RPi OS

  • สินค้าในสต๊อก:
    41

อุปกรณ์เสริมที่คุณอาจจะต้องการ

กรุณาใส่จำนวนที่ต้องการก่อนคลิกปุ่ม ‘เพิ่มในรถเข็น’

USB3.0 to 2.5" SSD Expansion board for RPi4B

USB3.0 to 2.5" SSD Expansion board for RPi4B

    THB1,267.47 THB1,347.18 Ex Tax: THB1,184.55

    • อุปกรณ์เสริมทั้งหมด: THB0.0
    • ผลรวมทั้งสิ้น: 988.47

    • รหัสสินค้า: MMR-2P5-MD-120
    • ระยะเวลาในการรับประกัน: 12 เดือน
    • ส่งจาก: Malaysia
    • Shipping:
    Note: This SSD comes Pre-loaded with Raspberry Pi OS and ready to boot up on Raspberry Pi 4 Model B (with latest bootloader firmware) or Raspberry Pi 400. Please DO NOT format it if you intend to use it with the Raspberry Pi board.
     

     

    2.5" SATA III SSD for Raspberry Pi 4 Model B and Raspberry Pi 400

    We, at Cytron Technologies, are pretty excited with the stable release of USB boot firmware and have also released a reliable SSD in 2.5" form factor. We called it MakerDisk! A Disk from Makers to Makers :) It is a 2.5" SATA III (6.0 Gbps) Solid State Drive (SSD) with a capacity of 120GB.

    Everyone is booting the preferred Operating System for the Raspberry Pi 4 Model B from USB :) The USB Boot firmware for Raspberry Pi 4 Model B is now officially released as a stable version. Check out this video by Jeff Geerling talking about the stable release of this firmware:

     

    Booting Raspberry Pi OS and opening Apps/Programs from MakerDisk SSD is faster than the microSD card. Here are the speed test results that we get using Raspberry Pi Diagnostics: (The MakerDisk is connected to Raspberry Pi through SSD Shield to USB3.0 port of Raspberry Pi 4 Model B).

    • Sequential write speed 280068 KB/sec (target 10000) - PASS, over 28 times faster than the target
    • Random write speed 14948 IOPS (target 500) - PASS, nearly 30 times faster than the target
    • Random read speed 13149 IOPS (target 1500) - PASS, nearly 9 times faster than the target

    Here is a comparison table between the 128GB Phidisk microSD and MakerDisk 120GB 2.5" SATA III SSD:

    Note: Raspberry Pi Diagnosis result depends on many factors (New memory or used memory, interface, SATA interface, USB interface, USB cable, etc). It should be taken as a reference only.

    This 2.5-inch MakerDisk SSD has a maximum sequential read and writes speed of up to 550MB/s and 460MB/s respectively. The above results are limited by the USB3.0 to SATA interface.

    Note: This MakerDisk SSD is PRE-LOADED with the Raspberry Pi OS, so you can use it with Raspberry Pi 4 Model B or Raspberry Pi 400 right out of the box (if the Raspberry Pi is ready with USB boot). Of course, you will still a SATA to USB bridge such as USB3.0 SATA Shield or USB3.0 to 2.5" SATA Adapter.

     

    Is Your Raspberry Pi 4 Model B or Raspberry Pi 400 Ready with USB Boot?

    Most of the latest Raspberry Pi 4 Model B comes with the latest USB bootable firmware. In case you have an older version of the Raspberry Pi 4 Model B board, or you are not sure, just check it using one of these methods:

    Option 1: Do it from Raspberry Pi OS desktop with a monitor, keyboard, and mouse, going into the raspi_config, by leepspvideo:

     
     
    Option 2: Format a blank microSD card (you need to back up the content in case you have only one microSD card) into FAT32, load the RPi4 EEPROM firmware using Raspberry Pi Imager(download from here). From Operating System -> Misc Utility Images -> Raspberry Pi 4 EEPROM boot recovery, choose your microSD card and load the image into it:
     

    After the Raspberry Pi Imager loaded the EEPROM firmware into the microSD card, insert it into your Raspberry Pi 4 Model B's microSD card slot and power it up. After just 3 seconds, the EEPROM is updated with new firmware and it is ready for USB boot.

    Option 3: Boot it directly if your Raspberry Pi 4 Model B comes with the latest firmware in the EEPROM, nothing needed to be updated :)

    In any case, you can always reload the image/Operating System into this SSD using a USB to 2.5" SATA Adapter or any compatible adapter. We recommend using the official imager: Raspberry Pi Imager. Please check this video out on how to use the Advance features:

    Features:

    • Brand: MakerDisk
    • Form factor: 2.5" SATA Solid State Drive
    • Pre-loaded with Raspberry Pi OS
    • Low power consumption
    • Low heat generation
    • High level of ability to endure shock, vibration, and high temperature
    • SMART & TRIM support
    • Host Interface: SATA III
    • Capacity: 120GB
    • Performance:
      • Read: Up to 550MB/s
      • Write: Up to 460MB/s
    • Shock: 1500G/0.5ms
    • Operation temperature: 0°C-70°C
    • Up to 20X faster than a typical hard disk drive
    • Boosts burst write performance, making it ideal for typical computer workloads
    • Faster boot-up, shutdown, application load, and response for Raspberry Pi

    Packing List:

    • 1 x 120GB 2.5-inch MakerDisk SATA III SSD with Raspberry Pi OS

     

    No questions have been asked about this product.

    Ask a question

    Note: HTML is not translated!
    • 0 out of 5
                    
    ความคิดเห็นทั้งหมด (0)
    • 5
      0%
    • 4
      0%
    • 3
      0%
    • 2
      0%
    • 1
      0%

    แท็ก: 2.5 inch, 2.5", Solid State Drive, Harddisk, harddisc, Raspberry Pi, Rpi4, RPI, USB Boot