New 38V Step Down 5V 5A Regulator

38V Step Down 5V 5A Regulator

    • Login to view ProMaker's Insider Price!
    • THB944.70(VAT included)
  • Ex Tax: THB882.90
    • 5 ชิ้นขึ้นไป THB897.03
    • 20 ชิ้นขึ้นไป THB850.23
    • 50 ชิ้นขึ้นไป THB802.56
  • เงินคืน: THB26.49
  • ยอดคงเหลือ CytronCash: เข้าสู่ระบบ
  • สินค้าในสต๊อก:
    13
  • รหัสสินค้า: VR-D24V50F5
  • ระยะเวลาในการรับประกัน: 12 เดือน
  • ส่งจาก: Malaysia

Note: The header pins included are not pre-soldered on the Regulator, you will need to solder it yourself.

 

This step-down (buck) regulator generates a fixed 5VDC output from input voltages up to 38VDC. It is a switching regulator (also called a switched-mode power supply (SMPS) or DC-to-DC converter) and has a typical efficiency between 85% to 95%, which is much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large. The available output current is a function of the input voltage and efficiency (see the Typical Efficiency and Output Current section below), but the output current can typically be as high as 5 A.

At light loads, the switching frequency automatically changes to maintain high efficiencies. The regulator has a typical quiescent current draw of less than 1 mA, and the ENABLE pin can be used to put the board in a low-power state that reduces the quiescent current to approximately 10 µA to 20 µA per volt on VIN.

This regulator has built-in reverse-voltage protection, short-circuit protection, a thermal shutdown feature that helps prevent damage from overheating, a soft-start feature that reduces inrush current, and an under-voltage lockout.

Features:

  • Input voltage: 6 VDC to 38 VDC (see below for more details on the regulator’s dropout voltage, which affects the low end of the operating range)
  • Fixed 5 VDC output (with 4% accuracy)
  • Typical maximum continuous output current: 5 A
  • Integrated reverse-voltage protection, over-current and short-circuit protection, over-temperature shutoff, soft-start, and under-voltage lockout
  • Typical efficiency of 85% to 95%, depending on input voltage and load; the switching frequency automatically changes at light loads to maintain high efficiencies
  • 700 μA typical no-load quiescent current; can be reduced to 10 µA to 20 µA per volt on VIN by disabling the board
  • Compact size: 0.7″ × 0.8″ × 0.35″ (17.8 mm × 20.3 mm × 8.8 mm)
  • Two 0.086″ mounting holes for #2 or M2 screws

Using the regulator: The connections

This buck regulator has five connection points for four different connections: enable (EN), input voltage (VIN), 2x ground (GND), and output voltage (VOUT).

The input voltage, VIN, powers the regulator and can be supplied with voltages up to 38 V. The effective lower limit of VIN is VOUT plus the regulator’s dropout voltage, which varies approximately linearly with the load from around 700 mV to around 1.5 V (see below for a graph of the dropout voltages as a function of the load).

The regulator is enabled by default: a 100 kΩ pull-up resistor on the board connects the ENABLE pin to reverse-protected VIN. The ENABLE pin can be driven low (under 0.6 V) to put the board into a low-power state. The quiescent current draw in this sleep mode is dominated by the current in the pull-up resistor from ENABLE to VIN and by the reverse-voltage protection circuit, which will draw between 10 µA and 20 µA per volt on VIN when ENABLE is held low. If you do not need this feature, you should leave the ENABLE pin disconnected.

The five connection points are labeled on the top of the PCB and are arranged with a 0.1″ spacing for compatibility with solderless breadboards, connectors, and other prototyping arrangements that use a 0.1″ grid. Either the included 5×1 straight male header strip or the 5×1 right-angle male header strip can be soldered into these holes. For the most compact installation, you can solder wires directly to the board.

The board has two 0.086″ mounting holes intended for #2 or M2 screws. The mounting holes are at opposite corners of the board and are separated by 0.53″ horizontally and 0.63″ vertically.

Typical efficiency and output current:

The efficiency of a voltage regulator, defined as (Power out)/(Power in), is an important measure of its performance, especially when battery life or heat are concerns. As shown in the graph below, these switching regulators have an efficiency of 85% to 95% for most combinations of input voltage and load.

The maximum achievable output current of the board depends on many factors, including the ambient temperature, airflow, heat sinking, and the input and output voltage.

Note:

During normal operation, this product can get hot enough to burn you. Take care when handling this product or other components connected to it. The over-current limit of the regulator operates on a combination of current and temperature: the current threshold decreases as the regulator temperature goes up. However, there might be some operating points at low input voltages and high output currents (well over 5 A) where the current is just under the limit and the regulator might not shut off before damage occurs. If you are using this regulator in an application where the input voltage is near the lower limit and the load could exceed 5 A for sustained periods (more than five seconds), consider using additional protective components such as fuses or circuit breakers.

 

Typical Dropout Voltage:

The dropout voltage of a step-down regulator is the minimum amount by which the input voltage must exceed the regulator’s target output voltage in order to ensure the target output can be achieved. For example, if a 5 V regulator has a 1 V dropout voltage, the input must be at least 6 V to ensure the output is the full 5 V. The following graph shows the dropout voltages for the D24V50F5 regulator as a function of the output current:

Switching frequency and behavior under light loads:

The regulator generally operates at a switching frequency of around 600 kHz, but the frequency drops when encountering a light load to improve efficiency. This could make it harder to filter out noise on the output caused by switching.

 

Packing List:

  • 1 x 38V Step Down 5V 5A Regulator
  • 1 x Right-angle 5-way male header pins
  • 1 x Straight 5-way male header pins

 

No questions have been asked about this product.

Ask a question

Note: HTML is not translated!
  • 0 out of 5
                  
ความคิดเห็นทั้งหมด (0)
  • 5
    0%
  • 4
    0%
  • 3
    0%
  • 2
    0%
  • 1
    0%

แท็ก: Step-down, D24V50F5, High voltage regulator, SMPS, switching module, 24V to 5V, 12V to 5V, 36V to 5V