Adafruit Gemma Mini Wearable V2

Adafruit Gemma Mini Wearable V2

    • Login to view ProMaker's Insider Price!
    • THB392.60(VAT included)
  • Ex Tax: THB392.60
    • 10 ชิ้นขึ้นไป THB353.34
    • 50 ชิ้นขึ้นไป THB314.08
  • เงินคืน: THB11.78
  • ยอดคงเหลือ CytronCash: เข้าสู่ระบบ
  • สินค้าในสต๊อก:


กรุณาใส่จำนวนที่ต้องการก่อนคลิกปุ่ม ‘เพิ่มในรถเข็น’

USB Micro B Cable

USB Micro B Cable

  • 10 ชิ้นขึ้นไป THB27.78
  • 100 ชิ้นขึ้นไป THB22.65

THB30.20 Ex Tax: THB30.20

Crocodile Clip with Wire (10pcs)

Crocodile Clip with Wire (10pcs)

  • 10 ชิ้นขึ้นไป THB47.11
  • 50 ชิ้นขึ้นไป THB44.17

THB49.08 Ex Tax: THB49.08

  • อุปกรณ์เสริมทั้งหมด: THB0.0
  • ผลรวมทั้งสิ้น: 392.6

  • รหัสสินค้า: AF-GMM-V2
  • ระยะเวลาในการรับประกัน: 12 เดือน
  • Shipping:

GEMMA is a tiny wearable platform board with a lot of might in a 1" diameter package. Powered by an Attiny85 and programmable with an Arduino IDE over USB, you'll be able to realize any wearable project!

Note: You will need a USB micro B cable to power and program the GEMMA V2 board, so grab it here if you don't have one.

Adafruit wanted to design a microcontroller board that was small enough to fit into any project, and low cost enough to use without hesitation. Perfect for when you don't want to give up your Flora and you aren't willing to take apart the project you worked so hard to design. It's Adafruit's lowest-cost sewable controller!

The Attiny85 is a fun processor because despite being so small, it has 8K of flash, and 5 I/O pins, including analog inputs and PWM 'analog' outputs. Adafruit designed a USB bootloader so you can plug it into any computer and reprogram it over a USB port just like an Arduino (it uses 2 of the 5 I/O pins, leaving you with 3). In fact Adafruit even made some simple modifications to the Arduino IDE. Perfect for small & simple projects, the GEMMA will be your go-to wearable electronics platform.

Even though you can program GEMMA using the Arduino IDE, it's not a fully 100% Arduino-compatible. There are some things you trade-off for such a small and low-cost microcontroller!

  • GEMMA does not have a Serial port connection for debugging so the serial port monitor will not be able to send/receive data
  • Some computers' USB v3 ports don't recognize the GEMMAs bootloader. Simply use a USB v2 port or a USB hub in between

Here are some example of  GEMMA projects you can try:

Features and specifications:

  • Super small, only 1.1" / 28mm diameter and 0.28" / 7mm thick.
  • Easy-to-sew or solder pads for embedding in your wearable project
  • Low cost enough, you can use one for every weekend project
  • ATtiny85 on-board, 8K of flash, 512 byte of SRAM, 512 bytes of EEPROM
  • Internal oscillator runs at 8MHz
  • Ultra low power, draws only 9 mA while running
  • USB bootloader with a nice LED indicator looks just like a USBtinyISP so you can program it with the Arduino IDE (with a few simple config modifications)
  • Micro-USB jack for power and/or USB uploading, you can put it in a box or tape it up and use any USB cable for when you want to reprogram.
  • We really worked hard on the bootloader process to make it rugged and foolproof
  • ~5.25K bytes available for use (2.75K taken for the bootloader)
  • On-board 3.3V power regulator with 150mA output capability and ultra-low dropout. Up to 16V input, reverse-polarity protection, thermal and current-limit protection.
  • Power with either USB or external output (such as a battery) - it'll automatically switch over
  • On-board green power LED and red pin #1 LED
  • Reset button for entering the bootloader or restarting the program.
  • 3 GPIO - The 3 independent IO pins have 1 analog input and 2 PWM output as well.
  • Hardware I2C capability for breakout & sensor interfacing.

Packing list:

  • 1 x Adafruit GEMMA v2 board


No questions have been asked about this product.

Ask a question

Note: HTML is not translated!
  • 0 out of 5
ความคิดเห็นทั้งหมด (0)
  • 5
  • 4
  • 3
  • 2
  • 1

แท็ก: GEMMA, Arduino, small, mini, ATtiny85