Grove Base Shield V2

THB245.14 (VAT included)
เงินคืน: 3%
  • 5 ชิ้นขึ้นไป THB232.46
  • 30 ชิ้นขึ้นไป THB220.62
  • สินค้าในสต๊อก: 27
    • ส่งจาก: Malaysia

    Buy locally from a partner

    ประเทศ:
    รายละเอียด
    Arduino Uno is the most popular Arduino board so far, however, it is sometimes frustrating when your project requires a lot of sensors or LEDs and your jumper wires are in a mess. Base Shield provides a simple way to connect with Arduino boards and helps you get rid of breadboard and jumper wires. With the 16 onboard Grove Connectors, you can easily connect with over 300 Grove modules! The pinout of Base Shield V2 is the same as Arduino Uno R3.
     
     
    There are 16 on-board Grove connectors including 4 x Analog, 7 x Digital, 1 x UART, 4 x I2C. Apart from the rich Grove connectors, on the board you can also see an RST button, a green LED to indicate power status, an ICSP pin, a toggle switch, and four rows of pinouts.
     
    Note: For all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using the product.

     

    This is one example of a project using the grove shield base:
     

     

    ระยะเวลาในการรับประกัน: 12 เดือน
    คุณสมบัติ

     

    • Power Compatible: Every Grove connector has four wires, one of which is VCC. However, not every microcontroller main board needs a supply voltage of 5V, some need 3.3V. That's why we add a power switch to Base Shield v2. In this way, you can adjust the voltage of VCC via this switch, making sure the voltage of VCC is the same as the supply power of the main board.
    • So While using Arduino UNO with Base Shield v2, please turn the switch to the 5V position; While using Seeeduino Arch with Base Shield v2, please turn the switch to 3.3v.
    • Board Compatible: The number of pinouts is the same as that of Arduino UNO R3 and other Arduino Uno compatible boards.
    • Added SDA and SCL pins that are near the AREF pin and two other new pins placed near the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board.

     

    Specifications:

    • Operating Voltage: 3.3V @ 5V
    • Operating Temperature: -25℃ to +85℃
    • Analog Ports: 4
    • Digital Ports: 7
    • UART Ports: 1
    • I2C Ports: 1
    • Weight: 40g
    • Dimension: 69mm x 53mm x 23mm

     

    Hardware Overview:

    1. Analog Ports: include 4 analog ports, A0, A1, A2, and A3.
    2. Digital Ports: include 7 digital ports, D2, D3, D4, D5, D6, D7, and D8.
    3. UART Port: 1 UART port.
    4. I2C Ports: 4 I2C ports.
    5. Power Switch: when using Arduino UNO with Base Shield v2, please turn the switch to the 5v position; While using Seeeduino Arch with Base Shield v2, please turn the switch to 3.3v.
    6. Reset Buton: reset the Arduino board.
    7. PWR LED: The Green LED turns on when powered on.
    8. P1, P2:please solder the pads P1 and P2, if using Base Shield v2 with Seeeduino V3.

     

     
     
    รายการบรรจุภัณฑ์
    • 1 x Grove Base Shield V2
    Q & A

    Ask a question

    ความคิดเห็น
    • 5 out of 5
                    
    เรียงตาม:

    แท็ก: ARDUINO SHIELD, GROVE, BASE SHIELD, ARDUINO GROVE, SEEEDSTUDIO base, shield, arduino, shields, shield-grove