รายละเอียด
* This is very new IoT development board, the community is working hard to get the guides and tutorials up, so it is for advance hackers only, at least for now.
This is the big brother of ESP8266 development board.
Nano32 is collaboration work by Makerasia and Gravitech from Thailand. It is base on ESP32 SoC. ESP32 the flagship product from Espressif (the company that design and produce ESP8266), but now with Xsensa Dual-Core 32-bit processors that case provide 600DMPIS. Let's look at the features and Specification of this board.
Nano32 (the development itself) Features:
ESP32 SoC (System on Chip) with WiFi and Bluetooth BLE
40MHz Crystal for CPU, 32.768KHz for RTC and low power operation
4MB Flash (32MBit)
FTDI231 for the USB to Serial communication
Auto-reset for automatic flash of new program
On board 3.3V, 0.5A LDO, tested to work upto 1A
2.5dBi Peak Gain, 0.5dBi averange gain antenna
Key Features of ESP32 SoC:
Xtensa® Dual-Core 32-bit LX6 microprocessors, up to 600 DMIPS
Integrated 520 KB SRAM
Integrated 802.11BGN HT40 Wi-Fi transceiver, baseband, stack and LWIP
Integrated dual mode Bluetooth (classic and BLE)
4 MByte flash (32Mbit)
2.2V to 3.6V operating voltage
-40°C to +125°C operating temperature
32 GPIO
ESP32 Wi-Fi Spec:
802.11 b/g/n/e/i
802.11 n (2.4 GHz), up to 150 Mbps
802.11 e: QoS for wireless multimedia technology
WMM-PS, UAPSD
A-MPDU and A-MSDU aggregation
Block ACK
Fragmentation and defragmentation
Automatic Beacon monitoring/scanning
802.11 i security features: pre-authentication and TSN
Wi-Fi Protected Access (WPA)/WPA2/WPA2-Enterprise/Wi-Fi Protected Setup (WPS)
Infrastructure BSS Station mode/SoftAP mode
Wi-Fi Direct (P2P), P2P Discovery, P2P Group Owner mode and P2P
Power Management
UMA compliant and certified
Antenna diversity and selection
ESP32 Bluetooth Spec:
Compliant with Bluetooth v4.2 BR/EDR and BLE specification
Class-1, class-2 and class-3 transmitter without external power amplifier
Enhanced power control
+10 dBm transmitting power
NZIF receiver with -98 dBm sensitivity
Adaptive Frequency Hopping (AFH)
Standard HCI based on SDIO/SPI/UART
High speed UART HCI, up to 4 Mbps
BT 4.2 controller and host stack
Service Discover Protocol (SDP)
General Access Profile (GAP)
Security Manage Protocol (SMP)
Bluetooth Low Energy (BLE)
ATT/GATT
HID
All GATT-based profile supported
SPP-Like GATT-based profile
BLE Beacon
A2DP/AVRCP/SPP, HSP/HFP, RFCOMM
CVSD and SBC for audio codec
Bluetooth Piconet and Scatternet
GPIO Peripherals:
3 x UARTs, including hardware flow control
3 x SPI
2 x I2S
12 x ADC input channels
2 x DAC
2 x I2C
PWM/timer input/output availabe on every GPIO pin
OpenOCD debug interface with 32 kB TRAX buffer
SDIO master/slave 50 MHz
Supports external SPI flash up to 16 MB
SD-card interface support
Security Related:
IEEE 802.11 standard security features all supported, including WFA, WPA/WPA2 and WAPI
Secure boot
Flash encryption
1024-bit OTP, up to 768-bit for customers
Cryptographic hardware acceleration:
Sensors Related Peripherals:
Ultra low noise analog amplifier
Hall sensor
10x capacitive touch interface
32 kHz crystal oscillator
Documents:
Videos:
Install Nano32 library in Arduino IDE
LED Blinking with Nano32 from Arduino IDE
ระยะเวลาในการรับประกัน: 12 เดือน
แท็ก: NANO32,
ESP32,
IOT,
WIFI nano32,
iot,
development,
board,
wifi